A parachute deployment bag serves multiple purposes.
- Protect the parachute from the ejection charge. Bags are usually made of Nomex cloth.
- Allows the bridle and suspension lines to be pulled tight before the parachute opens, preventing a large "jerk" on the system when the parachute inflates.
- Allows the parachute to move away from the rocket before it opens, helping prevent it from becoming tangled with the bridle, nose cone, fins, etc.
Deployment bags can be used with single-stage and two-stage recovery systems, though they are more commonly seen with two-stage recovery.
The descending rocket shown in Photo 1 is using a Rocketman R7 parachute. The yellow deployment bag can be seen floating above the parachute. The bag is attached to the apex of the parachute.
Most deployment bags used in model rocketry are "deployment sleeves" rather than much more complex bags. A description of different type of
deployment bags can be found in Theo W. Knacke's book "Parachute Recovery Systems Design Manual" (Para Publishing). Knacke's description of a deployment sleeve is below.
“The deployment sleeve is a long cylindrical container that fits loosely over the parachute canopy. Frequently the sleeve ends in a flap that folds over the lower part of the sleeve and is closed with suspension-line stow loops.”
Some deployment bags use a pilot chute to pull the bag off the main parachute, as shown in photo 2 which has an 18" pilot chute. Before the bag can be pulled off the parachute the bridle and suspension lines are pulled tight and away from the faster descending rocket. When the lines are tight the bag is pulled off the main parachute. Some deployment bags are designed to open and pull off the parachute without a pilot chute.
Rocketman deployment bags do not use a pilot chute. The author has modified Rocketman medium and large bags to use a pilot chute. Photo 2 shows an 18" pilot attached to a Rocketman medium bag. A short 1/4" tubular nylon bridle was added to the bag for pilot chute attachment.
Photo 3 is a clearer picture showing the attachment of the bridle to the top of the bag. The short 1/4" tubular nylon bridle was sewn to the bag by hand using carpet thread, which is available at any store with sewing supplies. The bridle ends in a loop, and the pilot's suspension lines are looped through the loop to attach the pilot to the bridle.
Photo 4 shows a Rocketman R7 parachute stuffed into a medium bag, and the pilot chute. The bag has not been closed yet, and therefore it is not yet ready for flight.
Two elastic loops can be seen on the bag. The flap has holes that match the loops. Final prepping of the bag for flight involved folding the flap over the bag, pulling the elastic loops through the holes, and then inserting the suspension lines through the elastic loops to hold the flap closed to protect the parachute and to prevent it from exiting the bag before the bridle and suspension lines are pulled tight.
The holes in the flap have been reinforced by sewing around them with carpet thread.
Photo 5 is a closeup of the elastic loops sewn to the bag using carpet thread.
Photo 6 shows the deployment bag's bridle which is attached to the top of the inside of the bag, and the apex of the parachute. This bridle is a standard part of all deployment bags so that the bag can be attached to the parachute and not float away when pulled off the parachute.
Photo 7 shows the flap folded over the bag. The suspension lines have not yet been inserted through the loops.
Photo 8 shows the suspension lines inserted through the elastic loops. The lines must go through the loops in a particular direction so that when pulled tight they easily pull out of the loops. If inserted in the wrong direction the lines may bind and not pull out of the loops.
The elastic loops only need to hold the suspension lines tightly enough that they don't fall out. The suspension lines should slide out when gently pulled. If the loops grab the suspension lines too tightly the pilot chute may not be able to pull the lines out of the loops.
This is another deployment bag. Circled, left to right, are the attachment for the pilot chute's bridle, the elastic loop that the suspension lines are placed through to keep the flap closed, and the hole in the flap. The pilot chute has not been attached yet. The bridle that runs to the apex of the main parachute is visible on the right.
One side of the flap is placed over the matching loop in photo 10. A closeup of the suspension lines through the elastic loop are shown in photo 11. The lines must be inserted in a particular direction so that they pull out when the bridle and suspension lines are pulled tight by the pilot chute.
Photo 12 shows a Rocketman R7 parachute stuffed into a deployment bags, and the suspension lines inserted into the loops. The pilot chute is not attached yet. Below the deployment bag is a 6" ruler for size comparison. The bag will easily fit in a 4" airframe. Because the bag will slide in a 4" diameter airframe shear pins should be used to retain the nose cone until the ejection charge fires.
Two deployment bags are displayed in photo 13. The top bag is a large Rocketman bag holding a Rocketman R14 parachute. It has a 22" pilot chute. The bottom bag has a Rocketman R7 parachute stuffed into it, and the pilot chute has not been attached yet. The same bags are shown from another angle in photo 14.
The pilot chutes attach to the tops of the bags. The suspension lines are placed through the elastic stow loops so that they pull out when the lines are pulled tight by the pilot chute.
Although deployment bags are usually made of Nomex cloth, a Nomex heat shield should be used between the ejection charge and deployment bag as additional insurance against a melted parachute.
The bag must be large enough so the whole parachute can be stuffed into it. A bag can be larger (wider and/or longer) than needed, but a bag must be slim enough to easily slide in an airframe.
A deployment bag should fit into an airframe without jamming or binding when stuffed with a parachute. If the bag is too wide use a narrower and longer bag or it may jam during deployment.
No magic formula exists to match a bag and parachute unless both are purchased from the same manufacturer. The same size parachute from two manufacturers may need different bag sizes because different parachute manufacturers use different materials. One parachute may need a larger bag because it is made from a heavier and bulkier material.
A simple bag can easily be constructed. This bag does not form a perfect cylinder because the bottom is not round. But it is simpler to construct than a bag that forms a cylinder.
- Nomex cloth.
- 1/4" tubular nylon or similar material for the bridles.
- Someone with cutting and sewing facilities.
Determine the maximum diameter for the bag. If the bag will be used with a 4" diameter airframe the bag should have a maximum diameter of about 3.5". A diameter of 3.5" translates into a circumference of about 11".
Circumference of a circle = 3.14 * diameter
3.14 * 3.5" diameter = 11"
If the bag (circle) is folded flat it would be 5.5" wide. to fit into a 4" diameter airframe without binding when stuffed with a parachute.
Each side of the bag should have a seam of at least 1/8" wide. Therefore each side of the bag needs to be 1/8" wider making the unsewn material 5.75" wide.
The bag's length depends upon the size of the parachute when compressed, which depends upon the parachute's size and material. Compress the parachute to the desired diameter and measure the needed length. A simple way to do that is to stuff the parachute into a cardboard tube of the desired diameter and then measure the length. For example, stuff a parachute into a 3" diameter tube to estimate the bag length for a 4" diameter airframe. Because the deployment bag will not be a perfect cylinder the measured length will be the approximate length. You should add a couple of inches to the bag's length. A bag that is a little long is much better than one that's too short. A bag that is too short is worthless.
Add 3"-4" to the length for the flap.
Put a small slot in the bottom of the bag and slide through the material for the bridle and sew the bridle into place.
Sew the bag and turn inside out so that the seams are on the inside. Add the elastic loops. Cut holes in the flap to match the placement of the elastic loops, and sew around the holes to reinforce them.
The method you will use to attach the bag to the parachute depends upon your parachute's construction. For a Rocketman parachute melt two holes through the suspension lines at the apex and run the bridle to the deployment bag through the holes. Some parachutes have a spill hole with lines running over the hole. For those attach the bag's bridle to the lines over the spill hole.
Submitted by Dean A. Roth